NEET 2023 Physics Question Paper with Answers
Updated 18 Nov 2026
50 NEET 2023 Physics questions with the correct answer and an explanation for each, chapter-wise. Tap “Show answer” under each question. No login needed.
- Q1· Semiconductor Electronics
A full wave rectifier circuit consists of two p-n junction diodes, a center-tapped transformer, capacitor and a load resistance. Which of these components remove the ac ripple from the rectified output?
- A. p-n junction diodes
- B. Capacitor
- C. Load resistance
- D. A center-tapped transformer
Show answer
Answer: B — Capacitor
The capacitor acts as a filter in the rectifier circuit, charging during peaks and discharging during troughs, which smooths out the pulsating DC output and removes the AC ripple.
- Q2· Electromagnetic Waves
In a plane electromagnetic wave travelling in free space, the electric field component oscillates sinusoidally at a frequency of 2.0×10^10 Hz and amplitude 48Vm^-1. Then the amplitude of oscillating magnetic field is: (Speed of light in free space = 3 × 10^8 ms^-1)
- A. 1.6 × 10^-8 T
- B. 1.6 × 10^-7 T
- C. 1.6 × 10^-6 T
- D. 1.6 × 10^-9 T
Show answer
Answer: B — 1.6 × 10^-7 T
Using E0/B0 = c, B0 = E0/c = 48/(3×10^8) = 16×10^-8 = 1.6×10^-7 T.
- Q3· Units and Measurements
A metal wire has mass (0.4 ± 0.002) g, radius (0.3 ± 0.001) mm and length (5 ± 0.02) cm. The maximum possible percentage error in the measurement of density will nearly be:
- A. 1.3%
- B. 1.6%
- C. 1.4%
- D. 1.2%
Show answer
Answer: B — 1.6%
Density = mass/(π r² l). Percentage error = (Δm/m) + (Δl/l) + 2(Δr/r) = (0.002/0.4) + (0.02/5) + 2(0.001/0.3) = 0.005 + 0.004 + 0.0066 = 0.0156 ≈ 1.6%.
- Q4· Alternating Current
In a series LCR circuit, the inductance L is 10 mH, capacitance C is 1 μF and resistance R is 100Ω. The frequency at which resonance occurs is:
- A. 15.9 kHz
- B. 1.59 rad/s
- C. 1.59 kHz
- D. 15.9 rad/s
Show answer
Answer: C — 1.59 kHz
At resonance, ω = 1/√(LC) = 1/√(10×10^-3 × 1×10^-6) = 1/√(10^-8) = 10^4 rad/s. Frequency f = ω/2π = 10^4/(2π) ≈ 1591.5 Hz ≈ 1.59 kHz.
- Q5· Kinematics
A football player is moving southward and suddenly turns eastward with the same speed to avoid an opponent. The force that acts on the player while turning is:
- A. along northward
- B. along north-east
- C. along south-west
- D. along eastward
Show answer
Answer: B — along north-east
Change in velocity ΔV = v(east) - v(south) = vî - (-vĵ) = vî + vĵ, which points in the north-east direction. Since force is in the direction of change in momentum/velocity, the force acts along north-east.
- Q6· Units and Measurements
The errors in the measurement which arise due to unpredictable fluctuations in temperature and voltage supply are:
- A. Personal errors
- B. Least count errors
- C. Random errors
- D. Instrumental errors
Show answer
Answer: C — Random errors
Random errors arise due to unpredictable fluctuations in experimental conditions like temperature, voltage supply, and other environmental factors, and cannot be eliminated completely but can be minimized by taking multiple readings.
- Q7· Dual Nature of Radiation and Matter
The work functions of Caesium (Cs), Potassium (K) and Sodium (Na) are 2.14 eV, 2.30 eV and 2.75 eV respectively. If incident electromagnetic radiation has an incident energy of 2.20 eV, which of these photosensitive surfaces may emit photoelectrons?
- A. Both Na and K
- B. K only
- C. Na only
- D. Cs only
Show answer
Answer: D — Cs only
Photoelectric emission occurs only when the incident photon energy exceeds the work function of the material. Since the incident energy (2.20 eV) is greater than Cs's work function (2.14 eV) but less than K's (2.30 eV) and Na's (2.75 eV), only Cs can emit photoelectrons.
- Q8· Kinematics
A bullet is fired from a gun at the speed of 280 m/s in the direction 30° above the horizontal. The maximum height attained by the bullet is (g = 9.8 ms^-2, sin 30° = 0.5):
- A. 2000 m
- B. 1000 m
- C. 3000 m
- D. 2800 m
Show answer
Answer: B — 1000 m
Maximum height H = u²sin²θ/(2g) = (280×280×0.25)/(2×9.8) = 19600/19.6 = 1000 m.
- Q9· Alternating Current
A 12V, 60 W lamp is connected to the secondary of a step down transformer, whose primary is connected to ac mains of 220 V. Assuming the transformer to be ideal, what is the current in the primary winding?
- A. 2.7 A
- B. 3.7 A
- C. 0.37 A
- D. 0.27 A
Show answer
Answer: D — 0.27 A
For an ideal transformer, input power equals output power: 220 × Ip = 60, so Ip = 60/220 = 0.27 A.
- Q10· Current Electricity
Resistance of carbon resistor determined from colour codes is (22000 ± 5%)Ω. The colour of third band must be:
- A. Green
- B. Orange
- C. Yellow
- D. Red
Show answer
Answer: B — Orange
22000Ω = 22 × 10^3 Ω. The third band represents the multiplier (10^3), which corresponds to the color Orange in the resistor color code.
- Q11· Atoms
In hydrogen spectrum, the shortest wavelength in the Balmer series is λ. The shortest wavelength in the Bracket series is:
- A. 4λ
- B. 9λ
- C. 16λ
- D. 2λ
Show answer
Answer: A — 4λ
For Balmer series shortest wavelength: 1/λ = R/4. For Bracket series shortest wavelength: 1/λ0 = R/16. Dividing: λ0/λ = 16/4 = 4, so λ0 = 4λ.
- Q12· Electrostatic Potential and Capacitance
The equivalent capacitance of the system shown in the following circuit is: [Circuit shows a 3μF capacitor from A in series with a parallel combination of two 3μF capacitors, connecting to B]
- A. 3 μF
- B. 6 μF
- C. 9 μF
- D. 2 μF
Show answer
Answer: D — 2 μF
The two 3μF capacitors in parallel combine to give 6μF. This 6μF is then in series with the first 3μF capacitor: CAB = (3×6)/(3+6) = 18/9 = 2μF.
- Q13· Nuclei
The half life of a radioactive substance is 20 minute. In how much time, the activity of substance drops to (1/16)th of its initial value?
- A. 40 minutes
- B. 60 minutes
- C. 80 minutes
- D. 20 minutes
Show answer
Answer: C — 80 minutes
Using A/A0 = 1/2^n, we get 1/16 = 1/2^n, so n = 4. Time t = n × T(half) = 4 × 20 = 80 minutes.
- Q14· System of Particles and Rotational Motion
The angular acceleration of a body, moving along the circumference of a circle, is:
- A. along the radius towards the centre
- B. along the tangent to its position
- C. along the axis of rotation
- D. along the radius, away from centre
Show answer
Answer: C — along the axis of rotation
Angular acceleration is a vector quantity whose direction is along the axis of rotation, as determined by the right-hand rule, similar to angular velocity.
- Q15· Mechanical Properties of Solids
Let a wire be suspended from the ceiling (rigid support) and stretched by a weight W attached at its free end. The longitudinal stress at any point of cross-sectional area A of the wire is:
- A. W/A
- B. W/2A
- C. Zero
- D. 2W/A
Show answer
Answer: A — W/A
Longitudinal stress is defined as force per unit cross-sectional area. Since the weight W is the force stretching the wire, stress = W/A at any cross-section along the wire.
- Q16· Electric Charges and Fields
An electric dipole is placed at an angle of 30° with an electric field of intensity 2×10^5 NC^-1. It experiences a torque equal to 4 N m. Calculate the magnitude of charge on the dipole, if the dipole length is 2 cm.
- A. 6 mC
- B. 4 mC
- C. 2 mC
- D. 8 mC
Show answer
Answer: C — 2 mC
Torque τ = pE sinθ = q(2l)E sinθ. So 4 = q × 2×10^-2 × 2×10^5 × 0.5, giving 4/2 = q × 10^3, so q = 2×10^-3 C = 2 mC.
- Q17· System of Particles and Rotational Motion
The ratio of radius of gyration of a solid sphere of mass M and radius R about its own axis to the radius of gyration of the thin hollow sphere of same mass and radius about its axis is:
- A. 5 : 3
- B. 2 : 5
- C. 5 : 2
- D. 3 : 5
Show answer
Answer: D — 3 : 5
For solid sphere: (2/5)MR² = Mk1², so k1² = (2/5)R². For hollow sphere: (2/3)MR² = Mk2², so k2² = (2/3)R². The ratio k1²:k2² = (2/5):(2/3) = 3:5. Note: this question was officially marked as Bonus (full marks awarded to all candidates) due to ambiguity between the ratio of radii of gyration versus their squares.
- Q18· Mechanical Properties of Fluids
The venturi-meter works on:
- A. Bernoulli's principle
- B. The principle of parallel axes
- C. The principle of perpendicular axes
- D. Huygen's principle
Show answer
Answer: A — Bernoulli's principle
A venturimeter is used to measure the flow speed of a fluid through a pipe, and its working is based on Bernoulli's principle, which relates pressure and velocity changes in a flowing fluid.
- Q19· Current Electricity
The magnitude and direction of the current in the following circuit is: [Circuit: A-2Ω-10V battery(E)-5V-1Ω-B on top path, D-7Ω-C on bottom path, forming a loop ADCB]
- A. 0.5 A from A to B through E
- B. 5/9 A from A to B through E
- C. 1.5 A from B to A through E
- D. 0.2 A from B to A through E
Show answer
Answer: A — 0.5 A from A to B through E
Using I = Vnet/Rnet = (10-5)/(1+2+7) = 5/10 = 0.5 A, flowing from A to B through E.
- Q20· Kinetic Theory
The temperature of a gas is -50°C. To what temperature the gas should be heated so that the rms speed is increased by 3 times?
- A. 3295 °C
- B. 3097 K
- C. 223 K
- D. 699 °C
Show answer
Answer: A — 3295 °C
V ∝ √T. Initial T1 = -50°C = 223 K. If rms speed increases 4 times (as shown in solution, 4V/V), then T2/T1 = 16, so T2 = 16 × 223 = 3568 K = 3568 - 273 = 3295°C.
- Q21· Semiconductor Electronics
Given below are two statements: Statement I: Photovoltaic device can convert optical radiation into electricity. Statement II: Zener diode is designed to operate under reverse bias in breakdown region. In the light of the above statements, choose the most appropriate answer from the options given below:
- A. Both statement I and statement II are incorrect.
- B. Statement I is correct but Statement II is incorrect.
- C. Statement I is incorrect but Statement II is correct.
- D. Both Statement I and Statement II are correct.
Show answer
Answer: D — Both Statement I and Statement II are correct.
Photovoltaic devices (solar cells) do convert optical radiation into electrical energy, and Zener diodes are indeed specifically designed to operate in reverse bias breakdown region for voltage regulation applications. Both statements are correct.
- Q22· Wave Optics
For Young's double slit experiment, two statements are given below: Statement I: If screen is moved away from the plane of slits, angular separation of the fringes remains constant. Statement II: If the monochromatic source is replaced by another monochromatic source of larger wavelength, the angular separation of fringes decreases. In the light of the above statements, choose the correct answer from the options given below:
- A. Both statement I and statement II are false.
- B. Statement I is true but Statement II is false.
- C. Statement I is false but Statement II is true.
- D. Both Statement I and Statement II are true.
Show answer
Answer: B — Statement I is true but Statement II is false.
Angular separation θ = λ/d, which does not depend on the screen distance D, so Statement I is true. Since θ = λ/d, increasing wavelength λ actually increases θ (not decreases), so Statement II is false.
- Q23· Waves
The ratio of frequencies of fundamental harmonic produced by an open pipe to that of closed pipe having the same length is:
- A. 2 : 1
- B. 1 : 3
- C. 3 : 1
- D. 1 : 2
Show answer
Answer: A — 2 : 1
For an open pipe, fundamental frequency f0 = v/2l. For a closed pipe, fundamental frequency fc = v/4l. The ratio f0:fc = (v/2l):(v/4l) = 2:1.
- Q24· Electromagnetic Induction
The magnetic energy stored in an inductor of inductance 4μH carrying a current of 2A is:
- A. 4 mJ
- B. 8 mJ
- C. 8 μJ
- D. 4 μJ
Show answer
Answer: C — 8 μJ
Energy stored E = (1/2)LI² = (1/2) × 4×10^-6 × (2)² = (1/2) × 4×10^-6 × 4 = 8×10^-6 J = 8 μJ.
- Q25· Ray Optics and Optical Instruments
Light travels a distance x in time t1 in air and 10x in time t2 in another denser medium. What is the critical angle for this medium?
- A. sin^-1(10t2/t1)
- B. sin^-1(t1/10t2)
- C. sin^-1(10t1/t2)
- D. sin^-1(t2/t1)
Show answer
Answer: C — sin^-1(10t1/t2)
v1 = x/t1 (speed in air/rarer medium), v2 = 10x/t2 (speed in denser medium). Refractive index μ = v1/v2 = (x/t1)/(10x/t2) = t2/(10t1). Critical angle: sin(ic) = 1/μ = 10t1/t2, so ic = sin^-1(10t1/t2).
- Q26· Current Electricity
If the galvanometer G does not show any deflection in the circuit shown, the value of R is given by: [Circuit: 10V source with 400Ω resistor in series to galvanometer G, R connected in parallel branch, 2V source on other side]
- A. 50 Ω
- B. 100 Ω
- C. 400 Ω
- D. 200 Ω
Show answer
Answer: B — 100 Ω
For null deflection, the voltage across R must equal 2V: 2 = [R/(400+R)] × 10. Solving: 800+2R = 10R, 8R = 800, R = 100Ω.
- Q27· Magnetism and Matter
The net magnetic flux through any closed surface is:
- A. Positive
- B. Infinity
- C. Negative
- D. Zero
Show answer
Answer: D — Zero
Since magnetic monopoles do not exist, magnetic field lines always form closed loops, so the net magnetic flux through any closed surface is always zero (Gauss's law for magnetism: ∮B·dA = 0).
- Q28· Thermodynamics
A Carnot engine has an efficiency of 50% when its source is at a temperature 327°C. The temperature of the sink is:
- A. 15 °C
- B. 100 °C
- C. 200 °C
- D. 27 °C
Show answer
Answer: D — 27 °C
Efficiency n = 1 - T2/T1. 0.5 = 1 - T2/600 (since 327°C = 600K). T2/600 = 0.5, so T2 = 300K = 27°C.
- Q29· Dual Nature of Radiation and Matter
The minimum wavelength of X-rays produced by an electron accelerated through a potential difference of V volts is proportional to:
- A. 1/V
- B. 1/√V
- C. V²
- D. √V
Show answer
Answer: A — 1/V
The minimum wavelength of X-rays is given by λmin = hc/(eV), so λmin is proportional to 1/V.
- Q30· Electromagnetic Waves
An ac source is connected to a capacitor C. Due to decrease in its operating frequency:
- A. displacement current increases
- B. displacement current decreases
- C. capacitive reactance remains constant
- D. capacitive reactance decreases
Show answer
Answer: B — displacement current decreases
Displacement current is proportional to frequency (Id = CdV/dt, and for AC, this scales with frequency). As frequency decreases, the displacement current decreases.
- Q31· Kinematics
A vehicle travels half the distance with speed v and the remaining distance with speed 2v. Its average speed is:
- A. 2v/3
- B. 4v/3
- C. 3v/4
- D. v/3
Show answer
Answer: B — 4v/3
Average speed for equal distances traveled at different speeds = 2v1v2/(v1+v2) = 2(v)(2v)/(v+2v) = 4v²/3v = 4v/3.
- Q32· Work, Energy and Power
The potential energy of a long spring when stretched by 2 cm is U. If the spring is stretched by 8 cm, potential energy stored in it will be:
- A. 4 U
- B. 8 U
- C. 16 U
- D. 2 U
Show answer
Answer: C — 16 U
U = (1/2)Kx². Since U ∝ x², and the extension increased from 2cm to 8cm (4 times), the new PE = (4)² × U = 16U.
- Q33· Mechanical Properties of Fluids
The amount of energy required to form a soap bubble of radius 2 cm from a soap solution is nearly: (surface tension of soap solution = 0.03 N/m)
- A. 5.06 × 10^-4 J
- B. 3.01 × 10^-4 J
- C. 50.1 × 10^-4 J
- D. 30.16 × 10^-4 J
Show answer
Answer: B — 3.01 × 10^-4 J
Work W = T(ΔA), and since a soap bubble has two surfaces, ΔA = 2×4πr². W = 0.03 × 4π×(0.02)² × 2 = 96π×10^-6 ≈ 300×10^-6 = 3.01×10^-4 J.
- Q34· Gravitation
Two bodies of mass m and 9m are placed at a distance R. The gravitational potential on the line joining the bodies where the gravitational field equals zero, will be (G = gravitational constant):
- A. -12Gm/R
- B. -16Gm/R
- C. -20Gm/R
- D. -8Gm/R
Show answer
Answer: B — -16Gm/R
At the null point where field is zero, Gm/x² = G(9m)/(R-x)², giving x = R/4. The potential at this point VP = -Gm/x - G(9m)/(R-x) = -Gm/(R/4) - 9Gm/(3R/4) = -4Gm/R - 12Gm/R = -16Gm/R.
- Q35· Electric Charges and Fields
If ∮E·ds = 0 over a surface, then:
- A. the magnitude of electric field on the surface is constant.
- B. all the charges must necessarily be inside the surface.
- C. the electric field inside the surface is necessarily uniform.
- D. the number of flux lines entering the surface must be equal to the number of flux lines leaving it.
Show answer
Answer: D — the number of flux lines entering the surface must be equal to the number of flux lines leaving it.
If the net flux through a closed surface is zero, it means the number of field lines entering the surface equals the number leaving it, as per Gauss's law (net enclosed charge could also be zero, but this doesn't guarantee field uniformity or constant magnitude).
- Q36· Atoms
The radius of inner most orbit of hydrogen atom is 5.3 × 10^-11 m. What is the radius of third allowed orbit of hydrogen atom?
- A. 1.06 Å
- B. 1.59 Å
- C. 4.77 Å
- D. 0.53 Å
Show answer
Answer: C — 4.77 Å
Since r ∝ n²/Z, r2 = r1 × (n2/n1)² = 5.3×10^-11 × 9 = 4.77×10^-10 m = 4.77 Å.
- Q37· Laws of Motion
A bullet from a gun is fired on a rectangular wooden block with velocity u. When bullet travels 24 cm through the block along its length horizontally, velocity of bullet becomes u/3. Then its further penetrates into the block in the same direction before coming to rest exactly at the other end of the block. The total length of the block is:
- A. 24 cm
- B. 28 cm
- C. 30 cm
- D. 27 cm
Show answer
Answer: D — 27 cm
Using v²=u²-2a(2×24): (u/3)²=u²-48a, giving a=u²/54. The block ends when v=0: 0=u²-2a·d, so d=u²/(2a)=u²/(2×u²/54)=27cm.
- Q38· Current Electricity
10 resistors, each of resistance R are connected in series to a battery of emf E and negligible internal resistance. Then those are connected in parallel to the same battery, the current is increased n times. The value of n is:
- A. 100
- B. 1
- C. 1000
- D. 10
Show answer
Answer: A — 100
In series: I = E/(10R). In parallel: nI = E/(R/10) = 10E/R. Dividing: n×E/(10R) = 10E/R, so n = 100.
- Q39· Alternating Current
The net impedance of circuit (as shown in figure) will be: [Circuit: series LCR with L=50/π mH, C=10^3/π μF, R=10Ω, connected to 220V, 50Hz AC source]
- A. 15 Ω
- B. 5√5 Ω
- C. 25 Ω
- D. 10√2 Ω
Show answer
Answer: B — 5√5 Ω
XL = 2πfL = 2π×50×(50/π)×10^-3 = 5Ω. XC = 1/(2πfC) = 1/(2π×50×(10^3/π)×10^-6) = 10Ω. Z = √(R²+(XL-XC)²) = √(10²+(10-5)²) = √125 = 5√5 Ω.
- Q40· Semiconductor Electronics
For the following logic circuit, the truth table is: [Circuit: A through NOT gate, B through NOT gate, both outputs into a NOR gate giving output Y]
- A. 0,0,0 / 0,1,1 / 1,0,1 / 1,1,1
- B. 0,0,1 / 0,1,0 / 1,0,1 / 1,1,0
- C. 0,0,0 / 0,1,0 / 1,0,0 / 1,1,1
- D. 0,0,1 / 0,1,1 / 1,0,1 / 1,1,0
Show answer
Answer: A — 0,0,0 / 0,1,1 / 1,0,1 / 1,1,1
Y = NOT(NOT A · NOT B) = A + B, which is an OR gate. Truth table: (0,0)→0, (0,1)→1, (1,0)→1, (1,1)→1, matching option 1.
- Q41· Current Electricity
The resistance of platinum wire at 0°C is 2Ω and 6.8Ω at 80°C. The temperature coefficient of resistance of the wire is:
- A. 3×10^-3 °C^-1
- B. 3×10^-2 °C^-1
- C. 3×10^-1 °C^-1
- D. 3×10^-4 °C^-1
Show answer
Answer: B — 3×10^-2 °C^-1
Using R = R0(1+αΔT): 6.8 = 2(1+α×80). Solving: α = 2.4/80 = 0.03 = 3×10^-2 °C^-1.
- Q42· Ray Optics and Optical Instruments
Two thin lenses are of same focal lengths (f), but one is convex and the other one is concave. When they are placed in contact with each other, the equivalent focal length of the combination will be:
- A. f/4
- B. f/2
- C. Infinite
- D. Zero
Show answer
Answer: C — Infinite
For lenses in contact, 1/F = 1/f1+1/f2 = 1/f + 1/(-f) = 0. So F = 1/0 = infinite, meaning the combination has no net converging or diverging power.
- Q43· Ray Optics and Optical Instruments
In the figure shown here, what is the equivalent focal length of the combination of lenses (Assume that all layers are thin)? [Figure shows a biconvex glass lens (n1=1.5) with liquid (n2=1.6) filled on both curved sides, R1=R2=20cm]
- A. -40 cm
- B. -100 cm
- C. -50 cm
- D. 40 cm
Show answer
Answer: B — -100 cm
The system consists of 3 lenses: two liquid plano-concave lenses (f1=f3=-100/3 cm each, using R/(μ-1) with μ=1.6) and the glass biconvex lens (f2=20cm, using R/(2(μ-1)) with μ=1.5). Combined: 1/F = 1/(-100/3) + 1/20 + 1/(-100/3) = -3/100+5/100-3/100 = -1/100, giving F = -100cm.
- Q44· Oscillations
The x-t graph of a particle performing simple harmonic motion is shown in the figure. The acceleration of the particle at t = 2s is: [Graph shows x oscillating between -1 and 1, with period T=8s, starting at x=0]
- A. -π²/8 ms^-2
- B. π²/16 ms^-2
- C. -π²/16 ms^-2
- D. π²/8 ms^-2
Show answer
Answer: C — -π²/16 ms^-2
ω = 2π/T = 2π/8 = π/4 rad/s. a = -ω²A sin(ωt) = -(π/4)²×1×sin(π/4×2) = -(π²/16)×sin(π/2) = -π²/16 ms^-2.
- Q45· Kinematics
A horizontal bridge is built across a river. A student standing on the bridge throws a small ball vertically upwards with a velocity 4 ms^-1. The ball strikes the water surface after 4s. The height of bridge above water surface is (Take g=10 ms^-2):
- A. 60 m
- B. 64 m
- C. 68 m
- D. 56 m
Show answer
Answer: B — 64 m
Using -h = ut - (1/2)gt² with u=4, t=4: -h = 4×4 - (1/2)×10×16 = 16-80 = -64, so h = 64m.
- Q46· Moving Charges and Magnetism
A very long conducting wire is bent in a semi-circular shape from A to B as shown in figure. The magnetic field at point P for steady current configuration is given by: [Figure shows two long straight wire segments with current i connected by a semicircular arc of radius R, point P at the center of the semicircle]
- A. μ0i/4R pointed away from the page
- B. (μ0i/4R)[1-2/π] pointed away from page
- C. (μ0i/4R)[1-2/π] pointed into the page
- D. μ0i/4R pointed into the page
Show answer
Answer: B — (μ0i/4R)[1-2/π] pointed away from page
The total field at P is the sum of contributions from the two straight segments and the semicircular arc. Combining these contributions gives Bp = (μ0i/4R)[1-2/π], pointed away from the page.
- Q47· Gravitation
A satellite is orbiting just above the surface of the earth with period T. If d is the density of the earth and G is the universal constant of gravitation, the quantity 3π/(Gd) represents:
- A. T²
- B. T³
- C. √T
- D. T
Show answer
Answer: A — T²
For a satellite orbiting just above Earth's surface, T² = 4π²R³/(GM). Substituting M = (4/3)πR³d: T² = 4π²R³/(G×(4/3)πR³d) = 3π/(Gd).
- Q48· Moving Charges and Magnetism
A wire carrying a current I along the positive x-axis has length L. It is kept in a magnetic field B = (2î+3ĵ-4k̂) T. The magnitude of the magnetic force acting on the wire is:
- A. √5 IL
- B. 5 IL
- C. √3 IL
- D. 3 IL
Show answer
Answer: B — 5 IL
F = I(L×B) = I(Lî × (2î+3ĵ-4k̂)) = IL[3k̂+4ĵ] (since î×î=0, î×ĵ=k̂, î×k̂=-ĵ). |F| = IL√(3²+4²) = 5IL.
- Q49· Electrostatic Potential and Capacitance
An electric dipole is placed as shown in the figure with -q and +q separated by 3cm each from center O, and point P is 5cm from the +q charge along the axis. The electric potential (in 10² V) at point P due to the dipole is (ε0 = permittivity of free space and 1/4πε0 = K):
- A. (5/8)qK
- B. (8/5)qK
- C. (8/3)qK
- D. (3/8)qK
Show answer
Answer: D — (3/8)qK
Distance from -q to P = 8cm, distance from +q to P = 2cm. VP = kq/2 - kq/8 = kq×10²[1/2-1/8] = (3/8)kq×10².
- Q50· Laws of Motion
Calculate the maximum acceleration of a moving car so that a body lying on the floor of the car remains stationary. The coefficient of static friction between the body and the floor is 0.15 (g=10 ms^-2).
- A. 150 ms^-2
- B. 1.5 ms^-2
- C. 50 ms^-2
- D. 1.2 ms^-2
Show answer
Answer: B — 1.5 ms^-2
For the body to remain stationary, the pseudo force must not exceed the maximum static friction: ma_max = μmg, so a_max = μg = 0.15×10 = 1.5 m/s².
Take NEET-style timed mocks with your rank
Full 720-mark mocks, NEET 2023 PYQs and instant analysis. Free for 30 days, no card.
Compare NEET course plans for every class.
Take NEET-style timed mocks with your rank
Full 720-mark mocks, NEET 2023 PYQs and instant analysis. Free for 30 days, no card.
Compare NEET course plans for every class.
Take NEET-style timed mocks with your rank
Full 720-mark mocks, NEET 2023 PYQs and instant analysis. Free for 30 days, no card.
Compare NEET course plans for every class.
Take NEET-style timed mocks with your rank
Full 720-mark mocks, NEET 2023 PYQs and instant analysis. Free for 30 days, no card.
Compare NEET course plans for every class.
More free practice: chapter-wise PYQs · NEET Question of the Day · Readiness Test